Stickers > Offset Printing > Square-Cut Stickers

Material colors may differ from actual colors depending on your monitor and resolution. [View Materials]

Size
Size	Trim Size Width x Height mm Design Size Width x Height mm
Paper Stock	후지반칼있음

Print Color
Quantity		sheets x design
Coating

Turnaround

Estimated turnaround is 3–5 business days from design preview approval and print start date.
Specialty finishing requires an additional 1–3 business days.

Every effort is made to meet the estimated turnaround. However, delays may occur subject to our production schedule.

Estimated delivery is based on Korean business days. Delivery may be delayed due to public holidays or customs processing in the destination country.

Important Pre-Order NoticeDetails Production GuideDetails

Color

Important information regarding print colors.

1. Printed colors will appear darker and less vivid than on your monitor.

Printing uses CMYK ink mixing to reproduce colors, which cannot identically match monitor colors.

Files submitted in Spot Color or RGB mode will be forcibly converted to CMYK. This may result in colors that differ from your expectations.

Due to the nature of gang-run printing, colors may print slightly lighter or darker, and variation between C (Cyan), M (Magenta), Y (Yellow), and K (Black) channels is expected.

Even with the same print data, color differences may occur depending on paper stock and print timing.
Due to the nature of gang-run printing, where multiple orders are printed simultaneously, precise color reproduction is difficult.
Large areas of dark background color may show roller marks, resulting in uneven color.
Even when the same color is used for front and back in the print data, the actual print results may differ.
If precise color reproduction is required, please provide a printed reference sample, place a dedicated-run order (press supervision available), or contact us via 1:1 Inquiry.
Gang-run products: Business Cards, Hang Tags, Coupons, Leaflets, Square-Cut Stickers, Kiss-Cut Stickers, Standard Envelopes, Gang-Run Flyers

2. Colors with similar CMYK ratios or sensitive tones may print very differently.

CMYK color deviation may result in significantly different printed colors. Color claims are evaluated based on the submitted print data, not the printed result.

Color deviation example: C=61%, M=52%, Y=52%, K=22%

When using sensitive colors with similar CMYK ratios — especially olive, gray, and brown tones — as a background, there is a very high probability of ink drift causing uneven, gradient-like variations within the same background area.
In gang-run printing, multiple orders are placed on a single plate, so ink supply is affected by the color ratios of surrounding jobs. This same variation will occur even with reprints.
This is an inherent characteristic of gang-run printing and does not constitute a defect or grounds for remake.

3. K=100% black is processed with overprint enabled.

If you do not want overprint applied, add 1% of another color to the black, or set the value to K=99%.

< Overprint K=100% >

< Overprint Off >

< Rich Black (C=30% + M=30%) >

< Overprint Example >

4. Patterns and textures require sufficient contrast with the background.

We recommend at least 20–30% color difference from the background.

< Color difference 10% >

< Color difference 20% or more >

< Patterns & Textures >

5. Use caution with text and lines made of mixed CMYK colors.

Slight misregistration between color plates may cause colors to spread or shift. This is more noticeable with thinner text and lines.
On dark backgrounds made of mixed CMYK colors, misregistration can cause thin elements to break up or disappear entirely.
For black text and lines, use pure black (K=100%) only. Do not use a mix of CMYK colors.
Even in a single color, extremely thin text or lines may not reproduce clearly in print.

6. Total CMYK ink coverage should be kept below 250%.

Higher ink density increases the risk of set-off (wet ink transferring onto adjacent sheets).
Pages may stick together, or ink may peel away from the surface.
For deeper tones, increase the K (Black) percentage rather than raising CMY values.
Depending on paper type and printing method, set-off can occur even below 250%.
Very high ink density may result in muddy dark tones or visible roller marks.

7. White ink printing is not fully opaque.

On transparent materials, show-through occurs in white ink printing. This is within normal range.

Adhesion Strength

Important information regarding sticker adhesion.

Adhesion performance varies by environment.

Sticker adhesion depends not only on the material manufacturer's specifications, but also on the surface material, temperature, humidity, and other environmental conditions of the application.
Even with the same material, adhesion properties may change over time after application. Please choose the appropriate material for your intended use.

We recommend testing with a small order instead of sample books.

Since adhesion performance changes over time, testing with an actual production run is more accurate than using sample books that may have been produced long ago.
Our production costs are reasonable, so we recommend placing a minimum quantity order to test in your actual environment before committing to a large run.

Important notice for bulk orders

Adhesion-related issues for bulk orders placed without prior testing are not eligible for exchange or refund.

Cutting

Important information regarding the cutting process.

A cutting tolerance of ±1–3mm (0.039–0.118 in) is the industry standard and does not constitute grounds for rework.

Large quantities are cut at once, which causes slight shifting.
Keep important content at least 3mm (0.118 in) inside the trim line on all sides.
For catalogs and brochures, at least 5mm (0.197 in) is recommended.
Borders and symmetrical designs cannot be guaranteed to cut evenly. Claims related to this are not accepted.
Shifting may result in slightly diagonal cuts.

Quantity

Quantity information for gang-run printing.

Due to the inherent nature of gang-run printing, a slight quantity shortage may occur. In most instances, this is maintained within 5%. However, subject to production conditions—including the ink density of other orders produced concurrently—a shortage of approximately 10% may, on rare occasions, arise.

If a significant shortage occurs, please contact us through our 1:1 inquiry.

Gang-run products: Business Cards, Hang Tags, Coupons, Leaflets, Square-Cut Stickers, Kiss-Cut Stickers, Standard Envelopes, Gang-Run Flyers
If finishing is included, additional waste may occur, increasing the shortage.
If exact quantity is required, please use dedicated-run printing.

InDesign

Size Setup

Select New and set the size for your print product. Set the page size to the trim size, and set the bleed in the Bleed section.

File → New → Document (Ctrl+N)

Intent: Print | Page Size: A4 (210×297mm) | Bleed: 3mm (all sides) | Slug: 0mm

Margin Setup

Set the safety zone in the Margins and Columns dialog. For small products (business cards, hang tags, coupons), use 3mm margins. For larger products (flyers, brochures, catalogs), use 5mm or more.

Layout → Margins and Columns

Margins: 3mm (all sides)

PDF Export

After completing your work, export as PDF with the following settings.

File → Export (Ctrl+E)

Format: Adobe PDF (Print) | Preset: PDF/X-4:2008 | Marks and Bleeds: Use Document Bleed Settings

Illustrator

Size Setup

Select New and set the size for your print product. Set the width and height based on the safety zone size. The trim size adds 3mm to each side (if using 3mm safety zone). The design size adds 6mm total. For small products (business cards, hang tags, coupons), use 3mm safety zone. For larger products (flyers, brochures, catalogs), use 5mm or more.

File → New (Ctrl+N)

Width: 297mm, Height: 210mm + 6mm | Bleed: 6mm (all sides) | Color Mode: CMYK | Raster Effects: High (300 ppi)

Convert Fonts to Outlines

All fonts must be converted to outlines.

Type → Create Outlines (Shift+Ctrl+O)

Outline Stroke

All strokes must be converted to outlines.

Object → Path → Outline Stroke

Overprint

Make sure to uncheck all overprint settings for fills and strokes.

Window → Attributes (Ctrl+F11)

Overprint Fill: unchecked | Overprint Stroke: unchecked

Transparency

Artwork using transparency must be flattened (100% vector).

Object → Flatten Transparency

Raster/Vector Balance: 100 (Vector) | Line Art and Text Resolution: 300 ppi | Gradient and Mesh Resolution: 150 ppi | Convert All Strokes to Outlines: checked

Rasterize

Any gradients, transparency effects, or other effects must be rasterized.

Object → Rasterize

Color Model: CMYK | Resolution: High (300 ppi) | Background: White / Transparent

Document Info Check

Check Document Info for potential print issues. Click Objects in the Document Info panel menu. All items should show "None" — if any show a number (2, 5, etc.), locate and fix those objects using the methods above.

Window → Document Info

Panel menu (☰) → Objects

Photoshop

Size Setup

Select New and set the size for your print product. Set resolution to 300 pixels/inch or higher, and color mode to CMYK. Note: Upscaling a low-resolution source will not improve quality. If your work was done at low resolution, you must recreate it from scratch at high resolution.

File → New (Ctrl+N)

Width: 216mm, Height: 303mm | Resolution: 300 Pixels/Inch | Color Mode: CMYK Color, 8 bit | Background Contents: White

Right-click ruler → Millimeters (or Edit → Preferences → Units & Rulers)

Order Cancellation and Refund

Refund policy for custom-made products.

As all products are custom-manufactured, refunds due to a simple change of mind are not available once production has begun.

If a defect caused by our error is confirmed, please file a claim through our 1:1 inquiry within 5 days of receiving the product. Defect determination is based on our quality standards.

Print errors caused by mistakes in the submitted file are entirely the responsibility of the customer and are not eligible for remake or refund.

Defect determination is based on our quality standards, using a comparison between the submitted file and the printed result.

To request a cancellation, please contact us through our 1:1 inquiry.

Before proof approval

Full refund available.

During production

Refund amount varies depending on production progress and is calculated based on our internal policy.

Before shipment

Product cost is non-refundable. Only shipping fees are refundable for unshipped orders.

Domestic Shipping ▼

Order Summary

Print Fee	15,800
Finishing Fee	0
Korean VAT	0
Shipping	0
Unit Price	₩ /ea
Total	₩ 17,380
(VAT Included)
* Shipping fees are subject to change based on destination.
17380	3000

Supplier	Reg. No.	334-86-03597
	Company	PLUBER	Name	Eun-Sun Ha
	Location	B-324, 70 Dusan-ro, Geumcheon-gu, Seoul 08595, Korea
	Business Type	Manufacturing	Industry	Offset Printing
	Tel	+82-2-6677-7333	Fax

Offset Printing

Small Qty (Digital)

Offset Printing

Small Qty (Digital)

Offset Printing

Small Qty (Outdoor)

Offset Printing

Imprinted

Offset Printing

Small Qty (Digital)

Offset Printing

Quote

Stickers > Offset Printing > Square-Cut Stickers

PLUBER

File Name	File Size
Drag and drop your file, or click to browse.